Magnehelic II® Differential Pressure Gages- Series 2-5000
Combining high accuracy, readability, compactness, dependability, and low cost.
Combining clean design, small size and low cost with enough accuracy for all but the most demanding applications our Minihelic II® gage offers the latest in design features for a dial type differential pressure gage. It is our most compact gage but is easy to read and can safely operate at total pressures up to 30 PSIG. The Minihelic II is designed for panel mounting in a single 2 5/8" diameter hole. Standard pressure connections are barbed fittings for 3/16" I.D. tubing; optional 1/8" NPT male connections are also available. Over-pressure protection is built into the Minihelic II gage by means of a blow-out membrane molded in conjunction with the diaphragm. Accidental over-ranging up to the rated total pressure will not damage the gage. With removable lens and rear housing, the gage may be easily serviced at minimum cost.
With the housing molded from mineral and glass filled nylon and the lens molded from polycarbonate, the gage will withstand rough use and exposure as well as high total pressure. The 5% accuracy and low cost of the Minihelic II gage make it well-suited for a wide variety of OEM and user applications. OEM applications include cabinet air purging, medical respiratory therapy equipment, air samplers, laminar flow hoods, and electronic air cooling systems. As an air filter gage, the Minihelic II finds many end use applications on large stationary engines, compressors, ventilators, and air handling units. Minihelic II gage is suitable for many of the same applications as the Magnehelic gage where the greater accuracy, sensitivity and higher and lower differential pressure ranges of the Magnehelic gage are not required.
| Ambient Temperature Range: | 20 to 120°F. |
|---|---|
| Rated Total Pressure: | 50 PSIG surge, 30 PSIG continuous to either pressure connection. |
| Accuracy: | plus or minus 5% of full scale at 70°F. |
| Connections: | Barbed, for 3/16" I.D. tubing (standard); male NPT (optional) |
| Housing: | Glass filled nylon; polycarbonate lens |
| Standard Ranges: | See model-range char |
| Finish: | Black |
| Weight: | 6 ozs |
CAUTION: FOR USE ONLY WITH AIR OR COMPATIBLE GASES
A:(left) The standard Minihelic II gage is supplied with two barbed pressure taps molded into the rear housing of the gage. These connections allow easy, fast connection to the gage using 3/16" I.D. rubber or plastic tubing.
B:(right) For applications in systems having higher total operating pressures optional male 1/8" NPT pressure connections can be supplied.
Note: the oblong over-pressure vent hole on the back of the gage at the right of connections. This vent is sealed by a membrane molded in conjunction with the diaphragm and will blow out at approximately 75 PSI.
- Housing is molded from strong mineral and glass filled nylon.
- Pointer stops of molded rubber prevent pointer over-travel without damage.
- Full view lens is removable and molded of tough polycarbonate.
- Aluminum scale litho-printed black on white, enhances readability.
- Red tipped aluminum pointer, rigidly mounted to helix is easy to see.
- Wishbone assembly provides mounting for helix, helix bearings, and pointer shaft.
- Jewel bearings provide virtually friction-free helix motion.
- Helix is free to rotate in jewel bearings. It aligns with magnetic field of magnet to transmit pressure indications to pointer.
- Zero adjustment screw, located behind the removable lens, eliminates tampering.
- Range spring calibration clamp fixes live length of spring for proper gage calibration and is factory set and sealed.
- Silicone rubber diaphragm allows accurate response to a broad range of temperatures and at extremely low pressure. Incorporates blow out area for overpressure protection.
- Diaphragm support plates of lightweight aluminum on each side of the diaphragm minimize position or attitude sensitivity and help define pressure area.
- Flat leaf range spring reacts to pressure on the diaphragm. Live length is adjustable for calibration. Small amplitude of motion minimizes inaccuracies and assures long life.
- Low pressure tap connects to rear chamber.
- Coil spring link provides a resilient connection between the diaphragm and the range spring
- Ceramic magnet mounted on a molded bracket at the end of the range spring rotates the helix without direct mechanical linkage
- High pressure tap connects with the front chamber through passageway in the plastic case and a sealing ring molded into the edge of the diaphragm
Mounting hardware is supplied with the Minihelic II gage for panel mounting through a single hole, 2 5/8" in diameter. Panel thickness up to 1/2" can be accommodated with the hardware supplied. If necessary, surface mounting of the gage can be accomplished by means of two 4-40 screws into the tapped mounting bracket stud holes in the rear of the gage. Surface mounting requires clearance holes in the panel for the two pressure taps.
| Model Number | Range Inches of Water | Minor Div. |
|---|---|---|
| 2-5000-0 2-5001 2-5002 2-5003 2-5005 2-5010 2-5020 2-5040 2-5060 2-5100 |
0-0.5 0-1.0 0-2.0 0-3.0 0-5.0 0-10 0-20 0-40 0-60 0-100 |
.02 .05 .10 .10 .20 .50 1.00 2.00 2.00 5.00 |
| Model Number | Range, PSI | Minor Div. |
| 2-5205 2-5210 2-5215 *2-5230 |
0-5 0-10 0-15 0-30 |
.2 .5 .5 1.0 |
| Model Number |
Range, MM of Water | Minor Div. |
| 2-5000-25MM 2-5000-50MM 2-5000-100MM |
0-25 0-50 0-100 |
1.0 2.0 5.0 |
| Model Number | Range Pascals | Minor Div. |
| 2-5000-125 Pa 2-5000-250 Pa 2-5000-500 Pa |
0-125 0-250 0-500 |
5.0 10 20 |
| Model Number | Range, kPa | Minor Div. |
| 2-5000-1 kPa 2-5000-3 kPa |
0-1 0-3 |
.05 .10 |
*This range employs spirally
wound
beryllium copper bound bourdon
tube pointer drive mechanism.
NOTE: Consult factory regarding
availability of additional
ranges.