Temperature Controller Series 1500
1/16 DIN, Microprocessor Based, Self ® PID
The Dwyer Series 1500 Temperature Controller is a reliable, accurate and fully programmable temperature control or alarm in an economical 1/16 DIN case. Microprocessor based, all control functions are easily programmed from the waterproof, corrosion resistant front panel. Models are available that accept field selectable J, K or T type thermocouples or RTD 100 DIN (.00385 ohms/ohm/°C) inputs and provide SSR, Relay or 5 VDC Logic outputs. All models are programmable for on-off, P, PI, manual PID or automatic Self-Tune® PID control. Like the control output, optional alarm is field configurable direct acting (cooling) or reverse acting (heating) and is easily adjusted for either automatic or manual reset to provide independent high or low system protection.
Four security levels are password protected. Electronics are easily replaceable via removable front panel (just pull out - no wiring changes) for quick upgrade to Dwyer Series 1600 Programmable Temperature/Process Controller. Front panel is designed to meet NEMA-4X.
| Inputs: | Thermocouple (J type stocked), field selectable K or T type; RTD (100Ohms DIN). |
|---|---|
| Input Impedance: | Thermocouple (3 megohms min.); RTD current (200 mA max.) |
| Accuracy: | ±0.25% of span ±1 least significant digit. |
| Displays: | 4 digit, 7 segment 0.3" high LED display; Set Point and Alarm status LED indicators; °F or °C LED indicators. |
| Temperature Range: | Operating -10° to 55°C (14° to 131°F); storage -40° to 80°C (-40°F to 176°F). |
| Supply Voltage: | 100 to 240 VAC, 50 - 400 Hz. single phase; 132 to 240 VDC (nom.) ±10% - 20%. 5 VA maximum power consumption. |
| Isolation: | Relay and SSR outputs are isolated. 5 VDC logic output must not share common ground with input. |
| Sensor Break Protection: | De-energizes control output. |
| Output Ratings: | SSR: 3.5A @ 240 VAC max. @ 25°C typical. Relay (SPST): 3A res., 1.5A ind. @ 250 VAC; Pilot Duty = 250 VA, 2A @ 125 VAC or 1A 01250 VAC, Logic (non-isolated): 5 VDC @ 25 mA max. |
| Alarm Rating (optional: Relay (SPST): | 3A res., 1.5A ind. @ 250 VAC. |
| Weight: | 227 9 (8 oz.). |
| Model | Input | Ouput | Alarm |
|---|---|---|---|
| 15011 | Thermocouple | SSR | No |
| 15111 | Thermocouple | SSR | Yes |
| 15012 | Thermocouple | 5 VDC Logic | No |
| 15112 | Thermocouple | 5 VDC Logic | Yes |
| 15013 | Thermocouple | Relay | No |
| 15113 | Thermocouple | Relay | Yes |
| 15021 | RTD (DIN) | SSR | No |
| 15121 | RTD (DIN) | SSR | Yes |
| 15022 | RTD (DIN) | 5 VDC Logic | No |
| 15122 | RTD (DIN) | 5 VDC Logic | Yes |
| 15023 | RTD (DIN) | Relay | No |
| 15123 | RTD (DIN) | Relay | Yes |
SUGGESTED SPECIFICATIONS
Temperature Controller shall be 1/16 DIN microprocessor based with 4 digit LED display, set point, optional alarm status and °F or °C LED indicators. Input shall be (selectable J, K or T type thermocouple) (DIN-RTD). Output shall be (SSR) (Relay) (5 VDC Logic) programmable for manual or automatic Self-Tune® PID control (with optional alarm). Front panel shall be designed to meet NEMA-4X rating for weather and corrosion resistance. Accuracy shall be ±0.25% of span ±1 least significant digit. Temperature controller shall be Dwyer Model D15_____.