View Master® Memory Stop
The memory stop is made from forged brass. Simply remove the handle nut, insert the 0-100% indicator pad over the stem, then insert the forged brass stop over the stm. Insert the allen screw into the stem, adjust the stop to the flow required for your application and tighten the screw. Now your valve will return to the same open position every time you cycle open to close to open.
| Type 1: | Fits T-100 and S-100 Models Sizes: ¼", ³/8", and ½" N.P.T. |
|---|---|
| Type 2: | Fits T-100 and S-100 Models Size: ¾" N.P.T. |
| Type 3: | Fits T-100 and S-100 Models Sizes: 1" and 1¼" N.P.T. |
| Type 4: | Fits T-100 and S-100 Models Sizes: 1½" and 2" N.P.T. |
Locking Device 100/82-3LD
Installation: Simply remove the Dacromet Nut from the handle and screw the three piece Locking Device over the outside stem thread with an Allen Wrench until it seats.
| Type 1: | Fits T-100 and S-100 Models ", ³/8", and ½" N.P.T. |
|---|---|
| Type 2: | Fits T-100 and S-100 Models Size: "N.P.T. |
| Type 3: | Fits T-100 and S-100 Models "and 1¼" N.P.T. |
| Type 4: | Fits T-100 and S-100 Models "and 2" N.P.T. |
| Type 5: | Fits T-100 and S-100 Models Sizes: 2½" and 3" N.P.T. |
Extended Handle
Installation: Remove the Dacromet Nut from the handle. Take the handle off. Screw in the two piece extension and replace the handle on the extension with an Open-end Wrench.
| Type 1: | Fits T-100 and S-100 Models Sizes: ¼", ³/8", and ½" N.P.T. |
|---|---|
| Type 2: | Fits T-100 and S-100 Models Size: ¾" N.P.T. |
| Type 3: | Fits T-100 and S-100 Models Sizes: 1" and 1¼" N.P.T. |
| Type 4: | Fits T-100 and S-100 Models Sizes: 1½" and 2" N.P.T. |
Slo-Ball® Handle
The 360° gear-closing handle allows metering of fluids and thus prevents hammering in pipes. Installation: Remove the Dacromet Nut from the handle. Take the handle off. Remove the yellow nameplate from the Slo-Ball. Place the Slo-Ball onto the valve. Screw in with a Phillips Screwdriver.
| Type 1: | Fits T-100 and S-100 Models Sizes: ¼", ³/8", and ½" N.P.T. |
|---|---|
| Type 2: | Fits T-100 and S-100 Models Size: ¾" N.P.T. |
| Type 3: | Fits T-100 and S-100 Models Sizes: 1" and 1¼" N.P.T. |
| Type 4: | Fits T-100 and S-100 Models Sizes: 1½" and 2" N.P.T. |
Round SS304 Handle
Installation: Remove the Dacromet Nut from the handle. Take the handle off. Place the round handle on the valve and replace the Dacromet Nut using an Open-End wrench.
| Type 1: | Fits T-100 and S-100 Models Sizes: ¼", ³/8", and ½" N.P.T. |
|---|---|
| Type 2: | Fits T-100 and S-100 Models Size: ¾" N.P.T. |
| Type 3: | Fits T-100 and S-100 Models Sizes: 1" and 1¼" N.P.T. |
| Type 4: | Fits T-100 and S-100 Models Sizes: 1½" and 2" N.P.T. |
| Type 5: | Fits T-100 and S-100 Models Sizes: 2½" and 3" N.P.T. |
| Type 6: | Fits T-100 Model Size: 4" N.P.T. |